Ask Proxima Projector C300HB User Manual

ASK Proxima C300 and C300HB (DP8000 and DP8000HB) Projectors  
Frequently Asked Questions: Lamp  
The image disappears or the lamp shuts itself off after a period of time.  
1. Verify that DPMS is not enabled.  
DPMS is the Display Power Management System. When it is on, the projector turns the lamp off after 3 minutes of  
not detecting an active source. The projector will return to normal activity immediately if it detects an active source.  
After 5 additional minutes, the projector turns off. You must press the Power button to turn the projector back on.  
The LED blinks green when in DPS mode.  
To disable or enable DPMS, press the Menu button on the keypad. Navigate to Basic > Setup > System. Select the  
DPMS Enable checkbox to enable the function, or clear the checkbox to turn it off.  
2. Is the LED on the keypad blinking red? If so, the projector may be overheating, which is frequently the result of a  
clogged dust filter. Try cleaning the dust filter on the bottom of the projector.  
3. If the problem persists, it is possible that there is an internal problem that requires repair. Take the projector to your  
dealer or contact ASK Proxima Technical Support.  
There is power to the unit and the fans are running, but no image is projected.  
1. Make sure the lens cap is off.  
2. Did the Fan Out message appear on the screen? If so, one of the fans inside the projector has stopped working. The  
projector automatically shuts down when it senses a inoperative fan. If this happens, the projector needs to be  
repaired at one of our repair depots. You can call or email ASK Proxima Tech Support to initiate this repair.  
3. Remove and reseat the lamp door. The lamp will not ignite if the lamp door is loose or is missing.  
4. Remove and reseat the lamp module.  
5. Replace the lamp. You can purchase a new lamp from your dealer.  
6. If the projector still will not display the image, it is may be that there is an internal problem that requires repair.  
Take the projector to your dealer or contact ASK Proxima Technical Support.  
What is the expected life of the lamp?  
The lamp life is approximately 1,500 hours. When the lamp timer reaches 1,500 hours, the Alarm LED on the projector will  
light red, indicating that it is time to replace the lamp. At this time you need to replace the lamp and reset the lamp timer.  
NOTE The expected lamp life is an approximation provide by the lamp manufacturer. Actual lamp life may vary depending  
on lamp usage, maintenance and manufacturing.  
How do I determine the number of lamp hours used?  
Press the Menu button, then navigate to Basic > Setup > Service. Select Info. The number of lamp hours appears in the  
Service Info window.  
How do I reset the lamp timer?  
In the menu of the projector, navigate to Setup > Service. Select the Reset Lamp Timer option, and press the Select button.  
When the Lamp Change window appears, click Select again to reset the timer. You can do this prior to 1,500 hours.  
What is the lamp warranty?  
Lamp modules are under warranty for defects for 90 days from the date of purchase of the projector or replacement lamp.  
Proof of purchase may be required.  
How do I install a new lamp?  
Lamp replacement instructions for this model can be found in your User Guide.  
Copyright © 1997-2004 InFocus Corporation.  
All Rights Reserved.  
 

Accusplit Heart Rate Monitor 605XE User Manual
Addonics Technologies Computer Drive DCDCS256S User Manual
AEG Range Ovens User Manual
Air King Vacuum Cleaner AKCVQZ80 User Manual
AIS Network Router AI2524 User Manual
Alcatel Carrier Internetworking Solutions Modem 3EC 16807 AAAA TCZZA ED 07 User Manual
Alliance Laundry Systems Washer B Series User Manual
Atlona TV Cables AT HDMI250SR User Manual
Avital Remote Starter 4111 User Manual
Beko Refrigerator CNE63721 DE User Manual